Groundwater
Pumps
Purging - Total Fluids
Pneumatic Pumps |
|
Portable
purging
pumps for use in monitoring wells. All are pneumatic (air-driven) pumps for maximum
reliability and explosion-proof operation. |
|
RENTAL GUARANTEE
Our pump are CLEANED & CHECKED |
|
|
QH23 |
|
QED
Hammerhead
Automatic Air Displacement Pump
The QED Hammerhead Air Displacement groundwater clean up pump allows simple groundwater bore purging in
50 mm and larger wells.
- Automatic operation (no external
controller required) - pumps after it has filled with water.
- Simple installation and quick to set up
- Flow rates to 9.5 LPM at shallow depths,
>6 LPM at 15m (@100psi supply pressure, 3m submergence)
- Stainless Steel Air Driven Pump NO Controller required, cycles itself
- Depth to 60 m head
- Bottom loading
- Pump Dimensions 44 mm x 100cm
- Pump volume per cycle, 250mL
- Hose size, Air inlet 1/4" (6mm) OD,
discharge 1/2" (12mm) OD, vent air 3/8" (10mm) OD
- Weight - Pump 3kg
- Pressure 10psi + 1.5psi per meter of head
- Requires compressed air source & hosing
|
|
|
|
|
|
Rental Rates
Purchase
Information
Hammerhead Flow Performance Curves
(19kb)
(refer to H23SEB - Bottom Inlet chart) |
|
|
|
|
AP4 |
|
AP4 Autopump
Automatic Air Displacement Pump
The Air Displacement groundwater clean up pump allows simple groundwater
bore purging in 100 mm and larger well.
- Automatic operation (no external
controller required) - pumps once filled with water.
- Simplest installation and quick to set
up
- Flow rates to ~20 liter/min (with 19mm
discharge hosing)
- FRP housing (SS for AP2) and SS, epoxy
float, brass quick connects for hoses
- Depth to 60 m head
- Pump Dimensions 90 mm x 1.32 m
- Hose size, Air inlet 10 mm OD,
discharge, 13 or 19 mm mm ID, vent 10 mm ID
- Air consumption 0.1 to 0.3 SCF/litre
- Pressure 10psi + 1.5psi per meter of
head
- Requires compressed air source & hosing
|
|
|
|
|
|
Rental Rates
Purchase
Information |
|
|
|
|
TAD42 |
|
Timco
Purge Pump
Air Displacement Pump with Controller
The Timco Air Displacement purge
pump allows simple groundwater bore purging in 50 mm and larger wells.
- Stainless Steel Air Driven Pump & Separate Controller
- Depth to 76 m head
- Pump Dimensions 42 mm x 1.2 m
- Hose size, Air inlet 6 mm OD, discharge, 12 mm OD
- Weight - Pump 5kg, controller 3 kg
- Controller Dimensions 20 x 18 x 15 cm
- Air consumption rate 5-7 cfm
- Pressure 10psi + 1.5psi per meter of head
- Requires compressed air source & hosing
|
|
|
|
|
|
Rental Rates
TAD Specifications
(45kb) |
|
|
|
|
TA4101REC |
|
12V Compressor
with Receiver Tank
- Very portable, 12 volt supply - connect to
the battery of a running motor vehicle.
- Light weight, easy to carry.
- Provides the reliability associated with
pneumatic pumps.
- Ensures you will be able to sample/purge
your bores every time and not have breakdowns usually associated with
electric pumps.
- Oil-less operation means no maintenance
required.
- Air Flow Rate: 0.9 cfm @ 100 psi, 2.2 cfm
open flow
|
|
|
|
|
|
Rental Rates
Purchase
Information |
|
|
|
|
TG180 |
|
TG180
Compressor
Petrol Driven, 4 horse power
This
large displacement compressor engine means you can drive most pumps at their full flow rate if needed down to over 85 m depths with conventional bladder or air displacement
pumps!
- Pumps faster & deeper than 12V
compressors
- No Electrical connections or Generator required
- Light enough to carry around by hand
- Entirely portable
- Oil-less operation means no maintenance
required
- Flow Rate - 4 cfm @ 100 psi
- 130 psi max pressure for lifts to 87m
- Engine - Honda 4HP, Petrol
- Automatic idle cuts engine speed back when
receiver tanks are at full pressure
- Internal pressure switch maintains
receiver tank pressure automatically
- Unloading valve for easy pull starting
- Pump-up time - approx. 1 minute
- Dimensions - 500 x 500 x 450mm high
- Weight - 35kg
Note: - Not to be used in indoors or poorly ventilated areas. Exhaust fumes contain carbon monoxide, an odourless and deadly gas |
|
|
|
|
|
Rental Rates |
|
|
|
|
LDPE Tubing is available for purchase |
|
|
|
|
