|
|
|
|
|
|
Portable
Bladder Pump |
_ |
QED Sample Pro Portable Micropurge® Pump |
|
|
|
|
|
The first portable bladder pump for MicroPurge® Low-Flow sampling.
The all-new Sample Pro Portable MicroPurge® Pump is the first pump developed specifically to bring the advantages of low flow sampling to sites requiring portable pumps. The Sample Pro Pump is not only able to deliver consistent low flow rates, it’s easy to disassemble without tools, simple to clean, and truly field rugged.
The SamplePro Portable MicroPurge® Pump uses a quick-change, one-piece bladder design. Compressed gas squeezes the outside of the bladder to force liquid out of the pump; there is no gas contact with the pumped water inside the bladder.
Water enters the pump through the inlet in the upper, head section, then flows down into the bladder. The high inlet helps keep the pump from clogging if it is accidentally lowered into a sediment-filled sump.
A replaceable inlet screen is provided for wells with high solids levels to help ensure proper sealing of the check valves. The Sample Pro Pump is shipped in a heavy-duty tube with rubber end caps to help keep the pump clean and protected between uses.
The pump is disassembled by a 1/4 turn of the cap and body; no tools are needed. The bladder pulls off for replacement. Both check valves are press-in, pull-out design, and use the same size Teflon check ball.
Compression-type and push-in tube fitting kits are available and can be used interchangeably. Both options provide high pull-out strength, but a cable eye is also included for applications where a support cable is desired.
|
|
| |
|
|
Controller & power option - MP15
Backpack |
|
Unlike other portable pumps, the Sample Pro is cool-running and can be operated by a lightweight backpack controller. There are no high speed rotating parts, no sample or motor heating, no costly maintenance or special generators.
Sample Pro reliability and low maintenance make it more economical. Its bayonet-type twist open design makes it easy to change the pull-off, disposable bladder in seconds. The compact 375 mm unit fits in a pail for pumping and cleaning.
Sample Pro innovations don’t stop there. The pump is available with conventional compression fittings for tubing connections, or with a “no fitting” push-in head that’s perfect for applications where the tubing is discarded frequently.
Sample Pro value and rugged, all-stainless construction will stand up to tough portable use. The simple yet effective design avoids the high maintenance expenses and destructive failure modes of other pumps.
Compact, rugged, and reliable, this is the first pump designed for low-flow operation in portable sampling applications.
Portable Controller Backpack w/ compressed gas supply gives you full independence
MP15 Backpack/Controller:
Low flow sampling is why the Sample Pro Pump was developed, and it matches perfectly with the new backpack-mounted MicroPurge® basics MP15 Control and Power Pack.
Flow adjustment with bladder pumps takes a completely new, simpler approach with the MP15 and the Sample Pro Pump. Up/down flow rate keys let you fine tune even low-flow rates easily and
repeatability.
At 12 kg with its high capacity gas cylinder, the MP15 backpack is a versatile companion to the Sample Pro Pump. A bypass fitting allows the MP15 to be used with larger compressed gas cylinders or a compressor for sampling sites which are vehicle-accessible.
|
|
|
Controller & power option - MP15
Backpack |
|
 |
|
Sampling Consultants Kit
The Sample Pro pump is also offered in this exclusive kit, which holds accessories and supplies in a rugged case that carries and protects the pump.
The kit includes all supplies, accessories and replacement parts necessary to sample 10 wells. The kit is packed in a 225x225x500 mm heavy duty case for easy portability on-site. |
|
|
|
|
|
|
|
System
Specifications |
| Model. |
Sample Pro Portable Sampling pump with inlet screen |
| Materials |
|
| Body |
316 Stainless
Steel |
| Inlet & Discharge Housing |
303
StainlessSteel |
| Bladder |
Polyethylene or Teflon® |
| O-rings |
Viton |
| Dimensions |
|
| Diameter |
1.75"(44.5mm) |
| Length: |
37.5
cm w/ Push-in Fittings; |
|
41.9
cm w/ Compression Fittings; |
|
30.8
cm Bottom of pump to centerline of inlet |
| Weight |
1.93
kg |
| Fittings |
Stainless
Steel Compression or Push-In Type |
| Air |
1/4"
(6.4 mm) O.D.,3/16" (4.7 mm) I.D. |
| Discharge |
3/8"
(10 mm) O.D., 1/4" (6.4 mm) I.D. |
| Maximum
Lift |
250
Feet (76 m) |
| Pump
Volume |
100mL |
|
| Ordering
Information |
|
Each pump includes pump, tube fitting kit, inlet screen and roving air fitting |
| QMP-SP-4P |
Portable SS pump 1/4”x1/4” push in fittings |
| QMP-SP-6P |
Portable SS pump 1/4”x3/8” push in fittings |
| QMP-SP-4C |
Portable SS pump 1/4”x1/4” compression fittings |
| QMP-SP-6C |
Portable SS pump 1/4”x3/8” compression fittings |
|
|
| Consultants Kit |
|
Includes pump, tube fitting, roving air fitting, tube cutter, cleaning brushes
plus 10 each - poly bladders, SS inlet screens, O-ring sets
plus 5 each - teflon check balls, and compression nut/ferrule sets for C type pumps
|
| QMP-SPK-4P |
Portable SS pump 1/4”x1/4” push in fittings |
| QMP-SPK-6P |
Portable SS pump 1/4”x3/8” push in fittings |
QMP-SPK-4C
|
Portable SS pump 1/4”x1/4” compression fittings |
| QMP-SPK-6C |
Portable SS pump 1/4”x3/8” compression fittings |
| Kit prices represent a saving of over 40% of the expendables |
|
|
| Pump Expendable Supplies |
| Q38360 |
Polyethylene bladder (10 pack) |
| Q38362 |
ORing kit (10 pack) |
| Q38361 |
Stainless steel inlet screns (10 pack) |
| Q38408 |
Teflon check balls (5 pack) |
|
|
|
|
For More information visit the QED
website. |
